Disc Fuel Oil Handling System for Liquid-liquid-solid Separation to Remove Solid and Water from Oil
Model PDSD8000 separator is mainly used to remove water and mechanical impurities from diesel oil, lubricating oil, and other mineral oil in marine diesel engine units and land-used diesel generator units of power stations so as to reduce wear of the diesel engine and other machines, and prolong engine life. The model is also used to separate two unsolvable liquids with different specific gravity or remove a small number of solid particles from a liquid.
The machine adopts automatic control and has the advantages of high efficiency, low oil consumption, convenient operation, and economic maintenance cost.
The clear oil and dirty water are pumped out by a centripetal pump, the sludge is discharged automatically and fully.
The machine is one kind of rotary machine with high speed. After accurate dynamic balancing, it can run for a long time with low vibration, safety, and security.
The design, product, and acceptance are conformed to the standard of GB/T5745 “Marine Disc Separator”.
Main Technical Specification for single machine
The output pressure of clear oil
L × W × H (mm)
1150 × 900 × 1500
Automatic control system
Water Control: Automatic control unlocking water, sealing water, and water-seal/water switching.
Pneumatic Control: Filter and adjust compressed air, control three-way changeover pneumatic valve.
Temperature Control: Automatic control of the temperature of the oil line, also control separately or with
electric control cabinet at the same time.
Buzzer Control: Monitor oil temperature, pressure, overloading, non-discharging, and leaking, and Offer a group of passive contractors stretching out to the control panel.
The whole unit consists of:
2. Electric control box
3. Oil feed pump
4. Oil filter
5. Pneumatic three-way valve
6. Ball valve
7. Pressure gauge
8. Vacuum gauge
9. Stop-check valve
10. 2/2 Solenoid valve
11. 3/2 Solenoid valve
12. Air reduction pressure valve
13. Brass filter ball valve
14. Water pressure-reducing valve
15. Temperature sensor
16. Liquid level switch
17. Sludge pump
1. According to the requirements of each classification society, all modules are equipped with oil leak alarms and high-temperature alarms.
2. Oil. hydraulic, pneumatic control part adopts the Brand Baode (Germany).
3. Heater adopts the brand SWEP (Germany).
4. Pressure control adopts Korean products or products
5. Screw pump is used instead of the gear pump.
6. All are equipped with automatic temperature control devices (Made by RTK production in Germany or made in China)
7. The main electrical components of the standard electrical control boxes are produced by Schneider company while PLC is produced by Siemens or Mitsubishi.
8. The complete sets referred to above are all Peony's production of automatic Standard Controls and we certainly can modify the configuration list according to customers’ specified requirements.
Peony organizes the model selection question as below:
1)How many kinds of oil can you separate?
This series separator is widely used for kinds of oils, especially for Marine diesel oil and similar oil, such as light fuel oil, heavy fuel oil, lubrication oil, steam turbine oil, detergence oil, engine oil, etc.
2)How can you select a suitable capacity?
Different oil has different capacity, our 1500L, 2000L, 3000L, 4000L, 5000L, 6000L, 8000L ,10000L capacity is for the Marine diesel oil 0# as sample. It also depends on the viscidity and temperature, and for all the capacity models, we have an oil characteristic sheet to help our customer to find out what their oil is, and what capacity their oil belongs to.
3) Is your separator self-cleaning?
We have 3 types of discharge means according to different materials and customer's requirements, we have the self-cleaning model and manual cleaning model.
1. Manual discharge model for the oil with very less solid component
2. Full discharge model for the big capacity treatment and a little solid component
3. Partly discharge model for the bigger capacity treatment and more solid component
4). Variable discharge model
No.full discharge type and partial discharge type are both self-cleaning models.
4)Will you help us to select the model?
Yes, you can select the model by yourself, or as long as you provide your material characteristic, we have a professional engineering team to help you select the suitable machine
5)Do you only have a single machine or a unit?
Both we have.
Peony Centrifuge has been dedicated to producing machinery and types of equipment and carrying out facility construction, pursuing the best quality and producing the best product at the same time.
We are committed to rewarding you with better quality in return for our interest in and faith.
We will do our utmost to one more step forward, based on our infinite services and trust in customers.